sglux-logo
bag-icon 1
Generic filters
Exact matches only
fr
  • Boutique
    • Photodiodes UV
    • TOCONs UV
      Photodiodes avec amplificateur de mesure intégré
    • Sondes de mesure UV
    • Radiomètres UV
    • Solutions personnalisées
    • Calibration UV
    • Mesure d’indice UV
    • Transducteurs de mesure pour photodiodes
  • Recherche
  • À propos
  • Contact
    • Distributeurs
    • Protection des données (en anglais)
    • Mentions légales
  • DE
  • EN
  • ES
  • FR

sglux

UV is our Business

  • DE
  • EN
  • ES
  • FR
Generic filters
Exact matches only
  • Boutique
  • Recherche
  • À propos
  • Contact
Accueil / Produit / TOCONs UV / UVA

UVA

Sensibilité spectrale de 309 à 367 nm, longueur d’onde du pic 331 nm,
classés par mesures d’intensités.

«TOCON Water PTFE Housing» a été ajouté à votre panier. Voir panier

6 résultats affichés

Vue en grille Vue en liste
  • TOCON_A4

    TOCON_A4

    UVA, environ 18 nW/cm² ... 18 µW/cm², TO5 à lentillePrix unitaire: 138,00€
    Description du produit
    • photodétecteur UVA avec amplificateur intégré
    • structure TO5 encapsulée hermétiquement avec lentille
    • signal de sortie 0 … 5 V
    • radiation maximale (limite de saturation) à 331 nm (sensibilité du pic) d’environ 18 µW/cm²
    • radiation minimale d’environ 1,8 nW/cm²
  • TOCON_A5

    TOCON_A5

    UVA, environ 18 nW/cm² ... 180 µW/cm², TO5 + diffuseurPrix unitaire: 138,00€
    Description du produit
    • photodétecteur UVA avec amplificateur intégré
    • structure TO5 encapsulée hermétiquement avec diffuseur
    • signal de sortie 0 … 5 V
    • radiation maximale (limite de saturation) à 331 nm (sensibilité du pic) d’environ 180 µW/cm²
    • radiation minimale d’environ 18 nW/cm²
  • TOCON_A6

    TOCON_A6

    UVA, environ 180 nW/cm² ... 1.8 mW/cm², TO5 + diffuseurPrix unitaire: 138,00€
    Description du produit
    • photodétecteur UVA avec amplificateur intégré
    • structure TO5 encapsulée hermétiquement avec diffuseur
    • signal de sortie 0 … 5 V
    • radiation maximale (limite de saturation) à 331 nm (sensibilité du pic) d’environ 1,8 mW/cm²
    • radiation minimale d’environ 180 nW/cm²
  • TOCON_A7

    TOCON_A7

    UVA, environ 1.8 µW/cm² ... 18 mW/cm², TO5 + atténuateurPrix unitaire: 138,00€
    Description du produit
    • photodétecteur UVA avec amplificateur intégré
    • structure TO5 encapsulée hermétiquement avec atténuateur
    • signal de sortie 0 … 5 V
    • radiation maximale (limite de saturation) à 331 nm (sensibilité du pic) d’environ 18 mW/cm²
    • radiation minimale d’environ 1,8 µW/cm²
  • TOCON_A8

    TOCON_A8

    UVA, environ 18 µW/cm² ... 180 mW/cm², TO5 + atténuateurPrix unitaire: 138,00€
    Description du produit
    • photodétecteur UVA avec amplificateur intégré
    • structure TO5 encapsulée hermétiquement avec atténuateur
    • signal de sortie 0 … 5 V
    • radiation maximale (limite de saturation) à 331 nm (sensibilité du pic) d’environ 180 mW/cm²
    • radiation minimale d’environ 18 µW/cm²
  • TOCON_A9

    TOCON_A9

    UVA, environ 100 µW/cm² ... 1.0 W/cm², TO5 + atténuateurPrix unitaire: 138,00€
    Description du produit
    • photodétecteur UVA avec amplificateur intégré
    • structure TO5 encapsulée hermétiquement avec atténuateur
    • signal de sortie 0 … 5 V
    • radiation maximale (limite de saturation) à 331 nm (sensibilité du pic) 1,0 W/cm²
    • radiation minimale d’environ 100 µW/cm²

Nous vous conseillons avec plaisir sur ce produit

Romana Sonnenberg
Romana Sonnenberg
Dipl.-Ing.

+49 (0) 30 53015211
Tilman Weiss
Tilman Weiss
Dr.-Ing.

+49 (0) 30 53015211

Warenkorb

Accessoires

  • TOCON Steel Housing

    TOCON Steel Housing

    structure en métal, M12x1, stable CEMstructure en métal pour tous les TOCONs, filetage M12x1Prix unitaire: 113€
    Description du produit
    • structure en métal pour tous les TOCONs
    • filetage M12x1, longueur 32 mm
    • tension d’entrée 7 – 24 V
    • tension de sortie 0 – 5 V
    • connecteur intégré, câble de 2 m inclus
  • TOCON_N Steel Housing

    TOCON_N Steel Housing

    structure en métal, M12x1, stable CEMstructure en métal pour les TOCON_N, filetage M12x1Prix unitaire: 113€
    Description du produit
    • structure en métal pour tous les TOCON_N
    • filetage M12x1, longueur 39,5 mm
    • tension d’entrée 7 – 24 V
    • tension de sortie 0 – 5 V
    • connecteur intégré, câble de 2 m inclus
  • TOCON PTFE Housing

    TOCON PTFE Housing

    structure en PTFE, M12x1, stable CEMstructure en PTFE pour tous les TOCONs (sauf les TOCONs à lentille), filetage M12x1Prix unitaire: 113€
    Description du produit
    • structure en PTFE pour tous les TOCONs (sauf les TOCONs à lentille)
    • filetage M12x1, longueur 31 mm
    • tension d’entrée 7 – 24 V
    • tension de sortie 0 – 5 V
    • connecteur intégré, câble de 2 m inclus
  • TOCON Water PTFE Housing

    TOCON Water PTFE Housing

    structure en PTFE, G1/4", étanchestructure en PTFE pour tous les TOCONs (sauf les TOCONs à lentille), filetage G1/4", étanchePrix unitaire: 113€
    Description du produit
    • structure en PTFE pour tous les TOCONs (sauf les TOCONs à lentille)
    • filetage G1/4″, étanche jusqu’à 10 bar
    • tension d’entrée 7 – 24 V
    • tension de sortie 0 – 5 V
    • connecteur intégré, câble de 2 m inclus
  • TOCON Water steel Housing

    TOCON Water steel Housing

    structure pour les TOCONs, G1/4", étanchestructure pour tous les TOCONs (sauf les TOCONs à lentille), filetage G1/4", étanchePrix unitaire: 113€
    Description du produit
    • structure en métal pour tous les TOCONs (sauf les TOCONs à lentille)
    • filetage G1/4″, étanche jusqu’à 10 bar
    • tension d’entrée 7 – 24 V
    • tension de sortie 0 – 5 V
    • connecteur intégré, câble de 2 m inclus
  • TOCON starter kit

    TOCON starter kit

    accessoire TOCON optionnelpour tests initiaux, compatible avec tous les photodétecteurs TOCONPrix unitaire: 20€
    Description du produit
    • kit de démarrage pour tests initiaux
    • signal de sortie 0 – 5 V
    • compatible avec tous les photodétecteurs TOCON

FAQ

What is a TOCON?
A TOCON is a UV photodetector that contains a SiC or a GaP detector chip and an amplifier circuit that outputs a voltage of 0 to 5 V. This output voltage is linear in proportion to the UV radiation intensity reaching the chip.
Which are the advantages and disadvantages compared with a photodiode?
Compared with a bare UV photodiode the TOCON’s big advantage is the amplifier’s position inside the TO5 metal housing and its close proximity to the detector. This construction protects the usually very low current levels generated by the detector chip from electromagnetic interference and also from moisture and pollution induced disturbances. A point to be considered of the TOCON is the lower dynamic range (approx. 3 orders of magnitude) compared with a SiC UV photodiode (10 orders of magnitude). To overdome this disadvantage we offer each TOCON type in many different amplification levels to avoid saturation and too low voltage output levels for nearly all applications.
Which are the advantages and disadvantages compared with a sensor probe?
A TOCON is smaller and much less expensive than a sensor probe. Additionally a TOCON is water pressure proof and hermetically sealed. A point to be considered is that at the presence of strong electromagnetic interferences or in case of excess voltage a sensor probe could be of a better performance. The reason is that a sensor probe contains more space that is needed for components that avoid problems caused by ESD or excess voltage.
Is the TOCON calibrated?
No, the TOCON is not calibrated. If required, the sglux calibration laboratory offers an individual calibration service including a calibration certificate. This document assigns the voltage output of one specific TOCON to the irradiation of a specific UV radiation source. As-delivered the TOCON is sensitive in the specified range. Example: A TOCON_ABC6 is sensitive between 180 nW/cm² and 1.8 mW/cm². This means that the TOCON will saturate (output voltage = input voltage) at approx. 1.8 mW/cm². At the lower end a radiation of 180 nW/cm² will still output a couple of mV. While selecting a TOCON, the most important thing to consider is to not illuminate the TOCON until saturation level. A saturation will not damage the TOCON but likely the voltage output will no longer be linear to the radiation input because any increase of radiation below the saturation point will not further increase the output voltage.
What is the maximum signal output of a TOCON?
The theoretical maximum signal output is always a little less (approx. 5%) than the supply voltage.
Do I need an external amplifier?
No, no additional amplifier is required.
How can I use my TOCON?
Please use a standard voltmeter to read out the signal. Caution! Wrong wiring of power supply can lead to immediate destruction of the device. Please refer to our application note delivered with the device.
What about the TOCON scatter?
A TOCON is a sophisticated product with many internal components. Many of these internal components, and especially the quantum efficiency of the UV-sensing SiC chip and the gain resistor value, have sample to sample scatter (variation). TOCONs are designed for a total scatter of +/-20% in signal and some devices will show greater variance. It is recommended that that when choosing a TOCON model for production, the TOCON should be chosen so that the 5V saturation level is TWICE the expected signal from the device under normal conditions and that under normal/design conditions, output voltage is about 2.5V. Customers are especially cautioned to AVOID SATURATION conditions. Saturation is when Signal voltage equals Power Supply Voltage (normally 5V). Saturation will not damage the TOCON but it can lead to PERSONAL SAFETY PROBLEMS or other DAMAGE due to unknown and potentially excess UV exposure levels.
What is the output pin impedance (or the drive capability) of the TOCON sensor?
The TOCON can drive resistive loads as low as 2 kOhms, but we recommend not to stress this limit unnecessarily. In normal environments an input impedance of >= 100 kOhm is recommended for the readout circuitry. In very harsh (EMI/EMC/noisy) surroundings impedances of >= 10 kOhm can be considered taking into account a slight reduction in output swing. The TOCON is stable for capacitive loads up to 30 pF under all circumstances. If more capacitive loading can not be avoided a series resistor of 10 Ohms … 100 Ohms may be required to ensure stability up to few hundred nF.
sglux GmbH 2024
Richard-Willstätter-Str. 8
D-12489 Berlin
Tel: +49 (0) 30 53 01 52 11
Mail: welcome@sglux.de
Mentions légales Protection des données
We do not use any cookies for tracking or analyzing of your website visit. However, technical cookies are needed to enable shop orders and to follow your language preferences.
Imprint | Privacy Policy
I accept cookies